Dbox2 Nokia 2xI Kabel nach 2 min geht aus !!!!

hallo

Dbox2 nokia 2xI kabel mit md-image5.02

Mein nachbarnnerin ist zu mir gekommen ob ich den dbox2 nokia2xI wieder in gang bringe,

nun bin ich ratlos den Ich habe so ein problem noch nicht gehabt...
also wenn mann den box mit strom versorgt und geht an, aber in tv bildschirm flimmert nur ca. 2 Minuten und geht dann aus. Das Display bleibt dunkel und ist dann nur ein punkt in farbe grün zusehen(Standby).

ich habe neue imgae geflasht aber kein erfolg immer das gleiche.

hhmmmm was kann man da noch machen?

Ich danke voraus

MfG
elmedin007

weiss keiner hier ... was man da machen kann ?

hier mal Bootlog

U-Boot 1.2.0 (Tuxbox) (Dec 16 2007 - 15:07:04)

CPU: PPC823ZTnnA at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
*** Warning: CPU Core has Silicon Bugs -- Check the Errata ***
Board: DBOX2, Nokia, BMon V1.0
Watchdog enabled
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: ....... done.
FB: ready
LCD: ready
In: serial
Out: serial
Err: serial
Net: SCC ETHERNET

Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select option (1-3), other keys to stop autoboot: 0
### FS (squashfs) loading 'vmlinuz' to 0x100000
### FS load complete: 694137 bytes loaded to 0x100000
............................................................... done
Un-Protected 63 sectors
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 694073 Bytes = 677.8 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.35.3-dbox2 (mdimage@mdimage-mdteam) (gcc version 3.4.6) #2 So
Dez 16 15:05:51 CET 2007
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: console=ttyS0 root=/dev/mtdblock1 rootfstype=squashfs
Decrementer Frequency = 252000000/60
m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
m8xx_wdt: keep-alive trigger installed (PITC: 0x1000)
Console: colour dummy device 80x25
Calibrating delay loop... 66.96 BogoMIPS
Memory: 30780k available (1180k kernel code, 348k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch ([email protected])
devfs: boot_options: 0x1
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
squashfs: version 3.0 (2006/03/15) Phillip Lougher
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
CPM UART driver version 0.04
ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:1b:e9:d9
loop: loaded (max 8 devices)
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
D-Box 2 flash memory: Found 2 x16 devices at 0x0 in 32-bit bank
Intel/Sharp Extended Query Table at 0x0035
cfi_cmdset_0001: Erase suspend on write enabled
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00420000 : "root (SquashFS)"
0x00420000-0x007e0000 : "var (JFFS2)"
0x007e0000-0x00800000 : "FLFS (U-Boot)"
0x00020000-0x00800000 : "Flash without bootloader"
0x00000000-0x00800000 : "Complete Flash"
Linux video capture interface: v1.00
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
init started: BusyBox v1.7.2 (2007-12-16 13:00:40 CET)
event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $
[i2c-8xx]: mpc 8xx i2c init
[i2c-8xx]: adapter: 0
Detected STB:
Vendor: Nokia
Model: D-BOX2
$Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $
$Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $
DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).
dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter
$Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $
avia_av: $Id: avia_av_core.c,v 1.99 2006/01/08 21:36:22 carjay Exp $
avia_av_core: Starting avia_av_wdt thread.
avia_av: timeout waiting for decoder init to complete. (00000001)
insmod: init_module: avia_av: Input/output error
insmod: unresolved symbol avia_av_set_stc
insmod: unresolved symbol avia_gt_gv_copyarea
insmod: unresolved symbol avia_gt_gv_show
insmod: unresolved symbol avia_gt_gv_get_clut
insmod: unresolved symbol avia_gt_gv_get_blevel
insmod: unresolved symbol avia_gt_gv_set_input_size
insmod: unresolved symbol avia_gt_gv_set_pos
insmod: unresolved symbol avia_gt_gv_hide
insmod: unresolved symbol avia_gt_get_info
insmod: unresolved symbol avia_gt_gv_set_size
insmod: unresolved symbol avia_gt_gv_set_input_mode
insmod: unresolved symbol avia_gt_gv_set_clut
insmod: unresolved symbol avia_gt_gv_set_blevel
insmod: unresolved symbol avia_gt_gv_get_info
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface
insmod: unresolved symbol avia_gt_ir_exit
insmod: unresolved symbol avia_gt_ir_receive_pulse
insmod: unresolved symbol avia_gt_ir_receive_data
insmod: unresolved symbol avia_gt_ir_get_rx_buffer_write_position
insmod: unresolved symbol avia_gt_ir_send_buffer
insmod: unresolved symbol avia_gt_ir_queue_pulse
insmod: unresolved symbol avia_gt_ir_init
insmod: unresolved symbol avia_gt_ir_set_duty_cycle
insmod: unresolved symbol avia_gt_ir_set_frequency
insmod: unresolved symbol avia_gt_ir_get_rx_buffer_read_position
insmod: unresolved symbol avia_av_set_sample_rate
insmod: unresolved symbol avia_gt_pcm_play_buffer
insmod: unresolved symbol avia_gt_pcm_stop
insmod: unresolved symbol avia_gt_pcm_set_signed
insmod: unresolved symbol avia_gt_pcm_set_endian
insmod: unresolved symbol avia_gt_pcm_set_rate
insmod: unresolved symbol avia_gt_pcm_set_width
insmod: unresolved symbol avia_gt_pcm_poll
insmod: unresolved symbol avia_gt_pcm_set_channels
insmod: unresolved symbol avia_av_get_sample_rate
insmod: unresolved symbol avia_gt_pcm_set_pcm_attenuation
insmod: unresolved symbol avia_gt_pcm_get_block_size
insmod: unresolved symbol avia_gt_pig_show
insmod: unresolved symbol avia_gt_pig_set_stack
insmod: unresolved symbol avia_gt_pig_set_size
insmod: unresolved symbol avia_gt_pig_set_pos
insmod: unresolved symbol avia_gt_pig_hide
DVB: VES1820(0): pwm=0x48
DVB: registering frontend 0:0 (VES1820 based DVB-C frontend)...
insmod: unresolved symbol avia_av_stream_type_set
insmod: unresolved symbol avia_av_register_video_event_handler
insmod: unresolved symbol avia_av_set_audio_attenuation
insmod: unresolved symbol avia_av_write
insmod: unresolved symbol avia_av_pid_set
insmod: unresolved symbol avia_av_audio_pts_to_stc
insmod: unresolved symbol avia_gt_dmx_queue_write
insmod: unresolved symbol avia_gt_dmx_enable_clip_mode
insmod: unresolved symbol avia_gt_dmx_disable_clip_mode
insmod: unresolved symbol avia_av_play_state_set_video
insmod: unresolved symbol avia_av_unregister_video_event_handler
insmod: unresolved symbol avia_av_get_video_size
insmod: unresolved symbol avia_av_play_state_set_audio
insmod: unresolved symbol avia_av_read
insmod: unresolved symbol avia_gt_pcm_set_mpeg_attenuation
insmod: unresolved symbol avia_av_new_audio_config
insmod: unresolved symbol avia_av_set_video_system
insmod: unresolved symbol avia_av_bypass_mode_set
insmod: unresolved symbol avia_av_sync_mode_set
insmod: unresolved symbol avia_gt_dmx_queue_nr_get_bytes_free
insmod: unresolved symbol avia_gt_dmx_get_ucode_info
insmod: unresolved symbol avia_gt_vbi_start
insmod: unresolved symbol avia_gt_dmx_queue_reset
insmod: unresolved symbol avia_av_napi_decoder_stop
insmod: unresolved symbol avia_gt_dmx_queue_stop
insmod: unresolved symbol avia_gt_dmx_queue_irq_enable
insmod: unresolved symbol avia_gt_dmx_set_pcr_pid
insmod: unresolved symbol avia_gt_vbi_stop
insmod: unresolved symbol avia_av_audio_pts_to_stc
insmod: unresolved symbol avia_gt_dmx_queue_write
insmod: unresolved symbol avia_gt_dmx_alloc_queue_teletext
insmod: unresolved symbol avia_gt_dmx_enable_clip_mode
insmod: unresolved symbol avia_gt_dmx_disable_framer
insmod: unresolved symbol avia_gt_dmx_disable_clip_mode
insmod: unresolved symbol avia_av_napi_decoder_start
insmod: unresolved symbol avia_gt_dmx_queue_start
insmod: unresolved symbol avia_gt_dmx_tap
insmod: unresolved symbol avia_gt_get_info
insmod: unresolved symbol avia_gt_dmx_enable_framer
insmod: unresolved symbol avia_gt_dmx_alloc_queue_video
insmod: unresolved symbol avia_gt_dmx_free_queue
insmod: unresolved symbol avia_gt_dmx_alloc_queue_audio
insmod: unresolved symbol avia_gt_dmx_alloc_queue_user
insmod: unresolved symbol avia_gt_dmx_get_stc
insmod: unresolved symbol avia_gt_accel_crc32
insmod: unresolved symbol avia_gt_napi_dvr_send
insmod: unresolved symbol avia_av_write
insmod: unresolved symbol avia_gt_set_playback_mode
insmod: unresolved symbol avia_gt_get_playback_mode
insmod: unresolved symbol avia_av_is500
insmod: unresolved symbol avia_av_read
insmod: unresolved symbol avia_av_new_audio_config
insmod: unresolved symbol avia_av_cmd

Please press Enter to activate this console. Thu Jan 1 01:00:00 CET 1970
mv: cannot rename '/lib/tuxbox/plugins/mdextra.cfg': No such file or directory
cdkVcInfo $Id: cdkVcInfo.c,v 1.0 2002/09/26 20:48:26 alexW Exp $

$Id: sectionsd.cpp,v 1.255 2007/12/16 11:53:31 seife Exp $
[sectionsd] Caching max 5000 events
[sectionsd] Caching 14 days
[sectionsd] Caching 6 hours Extended Text
[sectionsd] Events are old 60min after their end time
/var/tuxbox/config/zapit/epgfilter.xml: No such file or directory
/var/tuxbox/config/mybouquets.xml: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
$Id: zapit.cpp,v 1.404 2007/17/09 09:53:04 seife Exp $
[frontend] uncommitted_switch_mode 0
[sectionsd] getUTC: open: No such file or directory
/tmp/currentservices.xml: No such file or directory
[audio.cpp:CAudio:37] /dev/dvb/adapter0/audio0: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[video.cpp:CVideo:33] /dev/dvb/adapter0/video0: No such file or directory
[aviaext.cpp:CAViAext:37] /dev/dbox/aviaEXT: No such file or directory
$Id: controld.cpp,v 1.127 2007/07/01 08:40:13 dbluelle Exp $

[controld] Boxtype detected: (1, Nokia D-BOX2)
[controld] /dev/dvb/adapter0/video0: No such file or directory
[controld] /dev/dvb/adapter0/video0: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[controld]: ROUTEVIDEO v1 = 5 a1 = 1 v2 = 1 a2 = 1 v3 = 0 a3 = 1 fblk=1
[sectionsd] getUTC: open: No such file or directory
[yhttpd] Webserver nhttpd/3.1.6 (yhttpd_core/1.2.0)
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[LCDFONT] adding font /share/fonts/micron_bold.ttf...OK (Micron/Bold)
[LCDFONT] adding font /share/fonts/pakenham.ttf...[sectionsd] getUTC: open: No s
uch file or directory
OK (Pakenham/Regular)
[LCDFONT] Intializing font cache...
[sectionsd] getUTC: open: No such file or directory
[yhttpd] Webserver starting...
init(LCD_MODE_BIN): Device or resource busy
[sectionsd] getUTC: open: No such file or directory
[camd2] /dev/dvb/adapter0/demux0: No such file or directory
rm: cannot remove '/var/etc/.sectionsd': No such file or directory
[sectionsd] getUTC: open: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[sectionsd] getUTC: open: No such file or directory
neutrino: /lib/libpng12.so.0: no version information available (required by neut
rino)
[sectionsd] getUTC: open: No such file or directory
[sectionsd] getUTC: open: No such file or directory
starting /bin/neutrino
[neutrino] frameBuffer Instance created
/dev/fb/0: No such file or directory
framebuffer not available.
FBIOPUT_VSCREENINFO: Bad file descriptor
[sectionsd] getUTC: open: No such file or directory
FBIOGET_FSCREENINFO: Bad file descriptor
[neutrino] Error while setting framebuffer mode
zapit shot down
Waiting for controld (max. 9 seconds)
[sectionsd] getUTC: open: No such file or directory
Waiting for controld (max. 8 seconds)
[sectionsd] getUTC: open: No such file or directory
[sectionsd] getUTC: open: No such file or directory
Waiting for controld (max. 7 seconds)
[sectionsd] getUTC: open: No such file or directory
Waiting for controld (max. 6 seconds)
[sectionsd] getUTC: open: No such file or directory
Waiting for controld (max. 5 seconds)
[sectionsd] getUTC: open: No such file or directory
Waiting for controld (max. 4 seconds)
[sectionsd] getUTC: open: No such file or directory
[sectionsd] getUTC: open: No such file or directory
Waiting for controld (max. 3 seconds)
[sectionsd] getUTC: open: No such file or directory
Waiting for controld (max. 2 seconds)
[sectionsd] getUTC: open: No such file or directory
Waiting for controld (max. 1 seconds)
[sectionsd] getUTC: open: No such file or directory
[sectionsd] getUTC: open: No such file or directory
CXA2092 found
umount: cannot umount /var: Device or resource busy
The system is going down NOW!
Sending SIGTERM to all processes
[yhttpd] !!! SIGNAL !!! :15!
[yhttpd] No special SIGNAL-Handler:15!
[yhttpd] stop requested......
Sending SIGKILL to all processes
Requesting system halt

Dann geht dbox2 aus und an der display bleibt dunkel und ist nur led anzeige grün zusehen

Zitat von steinadler;209587

hi
schon verschiedene(andere) img probiert ?
denke aber mal das du ein koflikt zwischen hard.-und software haste
mach auch mal die box auf und schau ob der cpu oder andere teile verstaubt sind(hitzeproblem)

ja hab mehrere img probiert...und verstaubt ist es auch nicht...und hitze problem denke ich is es nicht, ich habe philips dbox es ist gleiche hitze zu fühlen.......
ich habe mitlerweile Keywelt image geflasht und geht zu mindest nicht mehr aus aber bei der TV bildschirm flimmert nur....und bei der Display mitlerweile geht auch nur es zeigt während er bootet das der kernel orndlich ladet und dann bei LCD logo als Linux Inside anzeigt und da bleibt hängen und tuts nichts mehr.

ich weiss nciht mehr was mann da machen kann( ein Netzteil zu wechseln kann mann bei Nokia dbox2 nicht...

Zitat von Rolli;209639

[color="White"]Das ist kein Netzteilproblem.
Ich vermute da eher einen defekten Flashbaustein.
Ob sich das dann noch lohnt, lasse ich mal dahin gestellt...->[/color][color="Red"]KLICK[/color]

dann wird wohl als defekt bei ebay gestellt.

danke trotzem an alle